My parts that i make to order. Waiting times vary from part to part. Cheers for looking!

Ghostbusters Sign:

1 unpainted moulding £10 (+£5 UK P&P, £8 Int. P&P)
2 unpainted mouldings £20 (+£5 UK P&P, £9 Int. P&P)
Complete painted sign £35 (+£6 UK P&P, £12 Int. P&P)

22cm (9") square by about 5cm (2")



_____________________________________________________________________________

Ion Arm: Aluminium and Brass (Inc. Hex nuts)
£15 +P&P




_____________________________________________________________________________

Black Tubing Kit (Non-Split, Small white line along length)

£9 +P&P




_____________________________________________________________________________

Cyclotron

£10 +P&P

Based on Stefans plans (black or white High Impact Polystyrene)




_____________________________________________________________________________

Lenses (Coloured transparent Acrylic - 1 Blue Powercell, 4 Red Cyclotron)

£4 +P&P




_____________________________________________________________________________

Brand New Light Kit:

£50 +P&P

NEW IMPROVED light kit - £50 plus postage and packing (Around $75 USD as of April 2010 - Depending on Currency Rates)

This is the newer version of the light kit I have offered in the past, now with a professionally produced PCB that offers a better looking and more efficient Proton Pack Light Kit.

The Kits lights up to the sequence shown in the movies and the speed can be controlled by a variable resistor for a personal touch to your pack. The circuit board itself will mount inside the Power cell and is 9.5cm high (Including LEDs) by 9.5cm wide. You could mount the board with Plasticine or Blue-tak easily enough.

It is made from the following:

A Printed Circuit Board (High quality professionally produced)
19 Ultra Bright White LED’s
19 x 470 ohm Resistors
20 x 10K Resistors
1 x 47K Resistor
1 x 47K Variable Pot Resistor
18 x Transistors
1 x 1uF, 1 x 10uF, 1 x 0.1uF Capacitors
1 x 555 Chip, 1 x 4017 chip, 2 x 4015 chips
Lots of wire

The Kit comes with a toggle switch, about 10 feet (x2) of wire to connect it to the Particle Thrower and a Battery clip for a 9V Battery (I have 4 packs using this kit and the battery has lasted a long time). The toggle switch is not soldered yet as you will need to thread them through your packs (The wires can be simply twisted together but I recommend soldering if you can).

The two sides of the completed PCB



The Battery Clip (Battery not supplied)


The Variable resistor that allows the cycle rate to be adjusted


The kit comes with a mini toggle switch for your Particle Thrower


Around ten feet of wire to connect to the toggle switch in the Particle Thrower (Colours may vary)


The Cyclotron Lights



15 ultra bright white Power Cell LEDs


The Light Kit in action (This video features the old PCB but works exactly the same way)

http://www.youtube.com/watch?v=vxdcBe7YwNE
The finished article mounted in the pack

http://www.youtube.com/watch?v=Yivz7HJtEnk

A link to my other parts: Plastic Cyclotron (£10), Ion Arm (£15), Acrylic Lenses (£4), Black Tubing Set (£9) Ghostbusters Sign (£10) - http://www.gbfans.com/community/viewtopic.php?f=31&t=11593

PM Me for postage, info and availability

JT94

Shame you don't do Trigger box's n' gun knobs

Awesome work there on the lighting kit for the pack

any plans on a gun lighting kit? or a sound kit even?

Excellent looking parts there JT, especially the lights set up.......good to see a UK based seller for a change, hope you do well mate.

Keith

Not at the moment, keep saying i'm going to look into it but just too busy at the moment.

JT

Did you get my PM JT?

I'm after an Ion arm

Hi there, Just browsing around, seeing what people have built/have on offer to give ideas for my own pack.

Whats the availability like for the light kits, cyclotron, an lense sets?

Just to let you know i'm back in business (had the same christmas/new year busy period at work as last year). There's a delay on Light kits at the moment as i'm waiting for some components to come in. Also waiting for hex screws for the Ion arms. PM me if you want something and i'll do mmy best.

JT

Will you be offering GB1 style ion arms in future?

Not exactly but I did drill out a hole for someone to put their own clippard brass elbow in. If there's enough demand and i can get a bulk order of the brass fittings then i could do i suppose.

JT